Longitudinal magnetic recording
Longitudinal magnetic recording stores HDD data with magnetization in the plane of the recording surface along the track direction.
Longitudinal magnetization lies along a track, while PMR magnetization points normal to the surface. The change involves different head and medium geometry, not simply a new software command. [3]
This is an orientation category, not the opposite of CMR. Non-shingled versus shingled describes track overlap. Historical use of the word conventional for longitudinal recording must not be read as the modern CMR/SMR taxonomy. [3] [4] [5]
A December 2004 PMR product announcement scheduled production for 2005; a November 2007 technical paper describes another company's PMR introduction in 2006. These milestones describe adoption of the successor technology, not a single worldwide end date for longitudinal HDDs. [4] [3]
The medium is a layer of weakly coupled CoCr-alloy grains, with chromium segregated to the grain boundaries and several hundred grains per bit cell for low noise. Smaller grains keep the signal-to-noise ratio as density rises but can reverse thermally, so KuV must exceed about 55 kBT to hold a signal for five years at about 340 K. [6] Modal grain size fell from about 20 nm to about 9 nm in a decade, a volume ratio of about 0.09. [7] [8]
A February 2005 technical report identifies demagnetizing fields and thermal instability as constraints on increasing longitudinal density. It explains a PMR head/media response, not a measured industry-wide investment shift or a universal date at which longitudinal recording stopped improving. [1]
Relations
- related
- Perpendicular magnetic recording (PMR), Conventional magnetic recording (CMR), Run-length limited (RLL) encoding, Hard disk drive (HDD)
- superseded by
- Perpendicular magnetic recording (PMR)
Advantages
- Grain-size control developed for chromium-segregated media was reused for the first perpendicular media. [6]
Limitations
- Shrinking grain volume raises thermal-stability concerns; a recording label alone does not establish a universal areal-density ceiling. [3]
- Write-pole materials stalled at 2.4 T saturation magnetization, so the higher anisotropy needed for stable smaller grains could not be written. [8]
- The easy-axis distribution is wider than the cone of about 5 degrees in perpendicular media, which costs signal-to-noise ratio. [8]
Citations
- Yoichiro Tanaka: Toshiba Review 60(2), February 2005, pp. 82-83, longitudinal scaling and PMR head/media design (Japanese)
- HGST: Perpendicular Magnetic Recording Technology, November 2007, sections 1.2-1.3 and Figure 1
- Toshiba: Perpendicular-recording HDD announcement, 14 December 2004
- Western Digital: Shingled Magnetic Recording Hard Disks, SMR overview and interface implementations
- Fu. Microstructure and Magnetic Properties of FePt/MgO Multilayered Thin Films. Master thesis, Vanderbilt University, December 2006.
- Lu and Laughlin. Microstructure of Longitudinal Media. The Physics of Ultrahigh-Density Magnetic Recording, Springer, 2001, chapter 2.
- Plumer, van Ek and Cain. New Paradigms in Magnetic Recording. Physics in Canada 67(1), 2011 (arXiv 1201.5543).
Further reading
Sources & caveats
- Historical HDD recording technology superseded in mainstream products by PMR; the cited sources establish PMR adoption milestones, not a global end-of-production or end-of-use date.
- Removed the unsupported lastSeen 2005 value. A PMR introduction milestone is not a global longitudinal-recording retirement or last-shipment date.
- PMR remains the orientation successor; CMR remains a related track-layout term. Existing slug, alias and citation c1 are preserved.
- Toshiba's December 2004 announcement gives planned production dates; HGST's November 2007 white paper describes its own introduction in 2006.
- The grain physics comes from a 2006 master thesis, a 2001 book chapter with a drive-maker co-author and a 2011 review with two drive-maker co-authors.
- The original 1997 thermal-stability paper and two journal articles on perpendicular media returned access errors and were not used.
- Arithmetic: (9/20)^3 is about 0.09; stability criteria of 55 kBT and 60 kBT differ by retention time and margin.