st-506 · end of life · also ST506

ST-506 interface

The ST-506 interface is an early hard-disk interface using raw step and head-select signals on a 34-pin cable and MFM or RLL data on a 20-pin cable, with the controller on a host adapter.

The 1982 OEM manual describes a drive of minifloppy size with a band actuator, stepper positioning and a 5.0 Mbit/s transfer rate. The 5 MB model has 153 cylinders, 4 heads, 3600 rpm, 6.38 MB unformatted (10,416 bytes per track) and 5.0 MB formatted (32 sectors of 256 bytes), 3 ms track-to-track, 85 ms average access with the fast seek algorithm and 8.33 ms latency. A seek selects the drive, sets the direction line and pulses the step line, each pulse moving the heads one track, at a minimum interval of 3 ms in slow-seek mode. [2]

The 34-pin control cable carries head select, write gate, seek complete, track 0, write fault, index, ready, step, drive select and direction; the 20-pin data cable carries differential MFM write and read data pairs and drive selected. MFM drives use 17 sectors per track and RLL drives 26, at 512 bytes per sector, and the RLL 2,7 code gives about 50 percent more data in the same bandwidth. [3] ESDI keeps both cables but moves the data separator onto the drive, whereas ST-506 designs put it on the controller. [3]

The ATA-1 draft describes putting the controller functionality inside the hard disk as the natural outgrowth of integration. [4] Arithmetic: 612 tracks x 8192 bytes = 5,013,504 bytes; 5 Mbit/s / 60 rev/s = 83,333 bits, about 10,417 bytes per track; half a revolution at 3600 rpm is 8.33 ms; 152 steps x 3 ms = 456 ms for a full-stroke slow seek; 26 x 512 / (17 x 512) = 1.53.

Relations

related
Hard disk drive (HDD), SCSI, ESDI, ST-412, IDE / ATA, Run-length limited (RLL) encoding, Floppy disk

Limitations

  • A drive should be used with an RLL controller only if certified for RLL, because RLL leaves less margin in the data window and demands better data-separator circuitry and steadier rotation. [3]

Citations

  1. ST-506 (accessed 2026-03-26)
  2. ST506 / ST412 OEM Manual, April 1982 (Seagate Technology) (accessed 2026-10-16)
  3. Hard Drive Bible, 3rd edition, 1991 (Corporate Systems Center) (accessed 2026-10-16)
  4. Information technology - AT Attachment Interface for Disk Drives, ATA-1 draft revision 4c (X3T9.2 draft of ANSI X3.221) (accessed 2026-10-16)
Sources & caveats
  • The OEM manual is the drive maker own 1982 document and the only description of the original interface read; signal timing and electrical levels were read only in outline and the earlier 1981 preliminary manual was not read.
  • The Hard Drive Bible is a 1991 commercial reference book by a company that is not a drive maker; it is independent of drive makers but is not a standards document.
  • The ATA-1 text is a standards-committee draft read as a mirrored copy and does not name ST-506.
  • Arithmetic: 612 x 8192 = 5,013,504 bytes matches the 5.0 MB formatted figure; 83,333 bits per revolution is about 10,417 bytes against 10,416 listed; 8192 / 10,416 is about 79 percent; 17 x 512 = 8704 bytes per track is 6.25 percent more than 8192.
  • Arithmetic: four head-select lines can address 16 heads against the four on this drive, so formatted capacity depends on the controller sector size and count, not on the drive alone.
  • No market, price or adoption statements are made.

JSON: /data/terms/st-506.json

Published by Hesela team · Updated

Report a correction · Editorial standards · Reuse guidance

Cite this page
Hesela team. ST-506 interface. Hesela. 2026-10-16. https://hesela.dev/terms/st-506/