wear-leveling · shipping · also wear levelling

Wear leveling

Wear leveling is flash management that distributes program/erase activity among blocks to reduce uneven wear.

Related Observatory article: Read on hesela.com

Dynamic and static policies differ in whether balancing includes relocation of unchanged data; firmware can use separate balancing groups. [5]

Erase-count balancing is not a guarantee against failure. Mohan and colleagues model both stress distribution and recovery intervals; their service-life results use workload-trace extrapolation, not five years of measured SSD survival [2]. Equal counts need not imply equal retention behavior or remaining endurance after thermal treatment [3].

Proactive relocation adds internal writes. The FTLSim study by Jiao and colleagues illustrates policy/workload tradeoffs, not a universal recommendation to disable wear leveling. [6]

The 2025 extension evaluates static policies with a capacity-shrinking interface. Its eleven-trace lifetime simulation assumes block retirement at 500 erases; this is a model input, not a measured universal NAND endurance limit. [8]

A threshold is part of a particular implementation, not a flash endurance rating: pinned Linux UBI uses a configurable erase-counter difference to trigger balancing. [9]

Relations

related
Flash translation layer (FTL), NAND flash, Solid-state drive (SSD), Write amplification, Bad block management, NAND channel, Planar NAND, Program/erase cycle, NAND dwell time, NAND self-recovery, Flash data retention, Dynamic wear leveling, Static wear leveling, READY

Citations

  1. Mohan et al. How I Learned to Stop Worrying and Love Flash Endurance. HotStorage 2010, sections 3 and 5. (accessed 2026-10-16)
  2. Buddhanoy et al. Life-after-Death: Exploring Thermal Annealing Conditions to Enhance 3D NAND SSD Endurance. HotStorage 2024. (accessed 2026-10-16)
  3. KIOXIA. Understanding Wear Leveling in NAND Flash Memory. February 2023, revision 1.0, pp. 1-2. (accessed 2026-10-18)
  4. Jiao, Bhimani and Kim. Wear Leveling in SSDs Considered Harmful. HotStorage 2022, sections 1-2. DOI 10.1145/3538643.3539750. (accessed 2026-10-18)
  5. Jiao and Yang. Wear Leveling in SSDs Considered Harmful: A Case for Capacity Variance. Electronics 14, 4169 (2025), sections 3-5. (accessed 2026-10-18)
  6. Linux UBI Kconfig at c7decec2f2d2ab0366567f9e30c0e1418cece43f: MTD_UBI_WL_THRESHOLD. (accessed 2026-11-05)

Further reading

  1. Wear leveling (accessed 2026-03-26)
  2. Hesela: 3D NAND retention, self-recovery and thermal annealing evidence (accessed 2026-10-16)
  3. Hesela: Wear Leveling, mechanisms and tradeoffs (accessed 2026-10-18)
Sources & caveats
  • The 2010 paper uses an analytical recovery model and trace extrapolation. [2]
  • The 2024 paper's sections 4-6 and figure 6 discuss thermal annealing; DOI 10.1145/3655038.3665949. CC BY 4.0; paraphrased, no figures reproduced. [3]
  • The 2025 article expands the 2022 work, not an independent replication. Its section 5 assumes negligible address-compaction overhead; wear-leveling-only write overhead is separate from total write amplification. CC BY 4.0. [8]

JSON: /data/terms/wear-leveling.json

Published by Hesela team · Updated

Report a correction · Editorial standards · Reuse guidance

Cite this page
Hesela team. Wear leveling. Hesela. 2026-11-05. https://hesela.dev/terms/wear-leveling/