NVMe backplane
An NVMe backplane is the board in a server or enclosure that carries PCI Express lanes, power and sideband signals to drive-bay connectors such as U.2 or EDSFF slots.
The U.2 receptacle (SFF-8639) is a six-lane, 68-contact connector whose mechanical interface accommodates single-port SATA, dual-port SATA Express, dual-port SAS, MultiLink SAS or up to four PCIe ports, adding four PCIe lanes and 10 sideband signals to the dual-port SAS set. It is rated 1.5 A continuous per power pin, 500 mA per signal pin and 0 to 55 °C, with 500 mate cycles in the backplane variant against 25 for cables. Link speed is defined in separate documents. [2]
For quad PCIe, the pinout uses +12 V pins P13 to P15 with pre-charge and +3.3 V auxiliary pin E3, while the +5 V pins serve only SATA and SAS. Sideband pins include power disable, presence detect, WAKE#, reference clock, PERST#, SMBus and DualPortEn#, and in dual-port mode each port gets two lanes. [3] Three 12 V pins at 1.5 A give the connector an upper bound of 54 W.
An E1.S slot uses a x4 or x8 card edge, with an initial power limit of 12 W for 5.9 and 8.01 mm devices or 25 W for 9.5, 15 and 25 mm, and up to 79.2 W at the 6.6 A, 12 V connector limit. [4]
Connector fit is not protocol support. SFF-8639 describes a shared mechanical interface, while a working bay also depends on wiring, controller mode, cabling and sideband support. The cited chassis guide distinguishes NVMe-only, SAS/SATA-only and mixed configurations; in its mixed configuration, only selected bays support either NVMe or SAS/SATA. [2] [6]
The cited direct-attached U.2 guidance requires the specified tri-mode cards and backplanes to use one connection mode per card: NVMe or SAS/SATA. It also specifies sideband requirements and a power cycle for changing cable types. These restrictions apply to that documented combination, not every tri-mode controller. [5]
Relations
- related
- U.2, EDSFF, PCIe storage attachment, PCIe lanes (storage), Dual-port drive, NVMe-MI, MCTP endpoint ID, Disk shelf, Serial Attached SCSI (SAS)
Advantages
- A supported mixed backplane offers a choice of drive protocols in designated bays; this flexibility is configuration-specific, not a guarantee for every U.2 bay. [6]
Limitations
- Mechanical fit alone does not establish protocol compatibility or arbitrary per-bay mixing. Check the exact backplane, controller, cable and sideband combination. [2, 5]
Citations
- SFF-8639 Rev 2.2: Specification for Multifunction 6X Unshielded Connector
- SFF-9639 Rev 2.1.1: Reference Guide for Multifunction 6X Unshielded Connector Pinouts
- SFF-TA-1006 Rev 2.0: Enterprise and Datacenter 1U Short Device Form Factor (E1.S)
- Supermicro FAQ 41383 (29 October 2024): direct-attached U.2 backplanes and named tri-mode cards
- Dell XC6520 Installation and Service Manual: chassis options and drive enumerations
Further reading
Sources & caveats
- c2 to c4 are SNIA SFF documents; c3 is SFF-9639 rev 2.1.1, a published draft with revision marks.
- SFF-TA-1002, SFF-TA-1009 and the PCI-SIG U.2 module specification were not consulted.
- Connector ratings alone do not establish switch topology, oversubscription, PCIe link speed or a system's hot-plug behavior.
- The 54 W figure is a connector bound, not a drive power budget, which the documents do not state.
- Arithmetic: 3 x 1.5 A x 12 V = 54 W; 6.6 A x 12 V = 79.2 W.
- The Dell and Supermicro examples are vendor configuration limits, not universal restrictions on U.2 or tri-mode hardware.
- Dell XC6520 chassis options identify the NVMe-only and selected universal-bay examples. Supermicro FAQ 41383 covers named storage cards and direct-attached U.2 backplanes, not all tri-mode hardware.