edsff · shipping · also Enterprise and Datacenter Standard Form Factor, Enterprise & Data Center SSD Form Factor

EDSFF

EDSFF is a family of standardized enterprise and datacenter device form factors whose members have distinct mechanical specifications and coordinated connector and electrical requirements.

Related Observatory article: Read on hesela.com

E1.S, E1.L, E2 and E3.S designate members of the family, not aliases for EDSFF. The older expansion containing SSD is retained as historical terminology; SFF-TA-1009 records the change to Standard Form Factor in 2021. E2 has its own mechanical specification, SFF-TA-1042. [5] [7]

The connector specification and device protocol are separate. SFF-TA-1002 is protocol-agnostic; matching the connector alone does not establish that a host supports a device's interface. [6]

Check the member, housing revision, cooling and platform qualification; EDSFF does not promise interchangeable bays or product capacity. [5] The E3.S 2T 2x1C arrangement needs a bay designed for that layout. SFF-TA-1008 recommends a keyed carrier to prevent insertion into incompatible bays; connector count alone does not establish compatibility. [2]

The E3 specification covers E3.S, E3.S 2T, E3.L and E3.L 2T devices for 1U, 2U and other hosts, plus an E3.S 2T 2x1C variant. Link widths are x4 (1C), x8 (2C, or two 1C connectors on the 2x1C variant) and x16 (4C and 4C+) from SFF-TA-1002, with signals in SFF-TA-1009 and thermal requirements in SFF-TA-1023. [2]

E3 initial slot power limits are 25 W (E3.S), 40 W (E3.L and E3.S 2T) and 70 W (E3.L 2T), E1.L lists 25 W, and the connector limit of 6.6 A at 12 V is stated as 79.2 W. This ceiling is further limited by the host and device operating environment. [2] [3]

The OCP v2.5 NVMe SSD profile requires E1.S and E1.L devices to follow SFF-TA-1006 or SFF-TA-1007, support at least PCIe Gen4 x4 and keep case temperature at or below 80 degrees Celsius, and requires E3 devices to follow SFF-TA-1008 and SFF-TA-1009, support separate reference clocks with independent spread-spectrum clocking and comply with PCI Express Base Specification 5.0 or later. [4]

Relations

related
E1.S, NVMe, Enterprise SSD, Flash module, U.2, M.2, PCIe 5.0 storage, PCIe lanes (storage), E1.L, E3.S, CXL memory expansion, E2

Limitations

  • E3.S and E3.L devices must carry a mechanical key slot so that systems can keep devices built to earlier revisions, which were not designed for direct liquid cooling, out of liquid-cooled hosts where they could suffer damaging pressure. [2]

Citations

  1. SFF-TA-1008 Enterprise and Datacenter Standard Form Factor (E3), Rev 3.0a, 10 July 2026 (SNIA SFF TWG) (accessed 2026-11-02)
  2. SFF-TA-1007 Enterprise and Datacenter 1U Long Device Form Factor (E1.L), Rev 1.3, 2 September 2025 (SNIA SFF TWG) (accessed 2026-11-02)
  3. Datacenter NVMe SSD Specification, Version 2.5, sections 10.5 to 10.7 (Open Compute Project) (accessed 2026-10-16)
  4. SNIA SFF-TA-1009 Rev 4.1a: section 1.1 and revision history (accessed 2026-10-18)
  5. SNIA SFF-TA-1002 Rev 1.6a: section 1, protocol-agnostic connector scope (accessed 2026-10-18)
  6. SNIA SFF-TA-1042 Rev 1.0 (16 June 2025): E2 abstract and scope (accessed 2026-10-19)

Further reading

  1. Enterprise and Data Center SSD Form Factor (accessed 2026-03-26)
Sources & caveats
  • The form-factor documents come from a storage industry association consortium and the NVMe specification from a consortium of operators and system makers; no university or government source on EDSFF was found, so independence is limited.
  • The SFF-TA-1008 file read is the published Rev 3.0a; a draft Rev 2.1.42 exists on the same site and was not used.
  • No capacity, price or adoption figures are given.
  • Arithmetic: 6.6 A x 12 V = 79.2 W; 76 x 112.75 x 7.5 mm is about 64.3 cm3 and 76 x 142.2 x 7.5 mm about 81.1 cm3, ignoring tolerances and the connector region.
  • The stable edsff ID and legacy SSD expansion are retained. Incorrect E1.L and E3.S aliases are replaced with separate related records.
  • The previous unqualified firstSeen value of 2020 is removed; this record does not assign a family invention or commercial-release date.
  • c1 remains legacy further reading; the revised definition and note rely on primary specifications.
  • 2026-11-01: preserved the later E3/E1.L dimensions and OCP profile while remapping citations from the earlier family correction. SFF-TA-1002 and SFF-TA-1009 have now been reviewed; packaging alone does not determine capacity or protocol support.

JSON: /data/terms/edsff.json

Published by Hesela team · Updated

Report a correction · Editorial standards · Reuse guidance

Cite this page
Hesela team. EDSFF. Hesela. 2026-11-02. https://hesela.dev/terms/edsff/